Shtenders

I built one from scratch when I was younger (15), it was allot of fun and it made me look forward to coming to davening. (Metoch shelo lishma ba lishma…)

Don’t use plywood or pressed wood spend the extra money and use cedar or oak. Start with 1″ X 12″ and choose a length depending on if you are building a tabletop or floor shtender. Go to your local Home Depot and choose a nice board with no knots.

Use screws instead of nails to hold the wood together (it lasts longer). You may also want to drill a .25 in wide pilot hole about .25 inches deep before driving the screws. You’d be surprised how easy it is to fill the cavity with wood putty and sand it smooth before applying the primer and finish.

Let me know if you have any other questions.

Good Luck

1) Tabletop or floor?

If floor:

2) What height?

3) What angle top?

4) What angle footrest?

5) How large a top surface?

6) How large a lip?

7) Do you want a closable top compartment?

8) If yes to 7, hinged top, hinged front or hinged side?

9) Do you want to keep seforim in the shtender?

10) If yes to 9, how many and how large?

The wood used is usually shelving pine and/or plywood. Don’t use pressed wood or particleboard of any type.

If you want to stain and varnish plywood, birch is nice, for painting luan is fine. Scraps are cheaper than a full sheet.

Molding, 1×2, iron-on or stick-on edging can also be used for the exposed plywood ends.

Go to yeshivos and shuls with a tape measure and sketch-pad, measure and draw designs you like, and (of course) try on shtenders for size, both while seated and while standing.

Circular saw

Drill

Electric screwdriver

Manual screwdriver

Router (sometimes, for notching or a decorative edge)

Hammer

Compound miter saw (makes cutting angles much easier)

Measuring tape

C-clamps (for holding work in place before fastening and after gluing)

Countersink drill bit(s) (depending on how well-finished you want the completed product to be)

Chisel (for hinges)

Once you have a design in mind, come back with more specific questions.

This is a very basic and simple design.

Alter measurements to fit your personal preferences.

From the bottom up:

feet: 4] 15″ 1×3

feet: 4] 3.75″ 1×3

sides: 2] 4′ 1×8. Cut tops to preferred angle. (four feet is quite tall – I suggest you measure an existing shtender to confirm your preferred height)

footrest supports: 2] triangular 7.5″ pieces of 3/4″ plywood, cut to the desired footrest angle (i.e. .5″ x 7.5″ x 1.5″)

footrest: 1] 16.5″ 1×8

shelf: 1] 16.5″ 1×8

shelf lip: 18″ 1×2

shelf back: 1] 18″x12″ plywood (or 18″ 1×12 shelving pine)

top 1] 14″x20″ 3/4″ plywood

top lip: 1] 20″ quarter-round molding (height your preference)

1) the 1×8 side pieces will fit vertically into the rectangular hole.

Use carpenter’s glue on all joined surfaces.

The bottom of the side pieces should be flush with the bottom of the feet.

Make sure the side pieces are vertical when the feet are on a straight floor.

use 2″ screws, since the total width of the feet will be 2.25″

The feet will look as follows, viewed from above:

|||

| |

|||

the outer layers are the 15″ 1×3’s, the inner layer is the 3.75″ 1×3’s with a 7.5″ gap for the vertical pieces.

2) glue and screw the angled 7.5″ pieces of plywood to the inside of the side pieces, resting on the feet.

use 1.25″ screws

3) glue & screw the footrest into place. you can drop a couple of screws from the top of the footrest into the angled plywood, and a couple of screws thru the sides into the footrest’s ends. Keep in mind that you dont want to split the wood, and end-grain isn’t that strong, so I’d use 1.25″ screws from the side & 1 5/8″ screws from the top.

Once the footrest is fastened, make sure the side pieces are vertical when the feet are on a straight floor.

4)Fasten the shelf back on the outside of the verticals at the top of the back of the shtender.

(the shelf back and shelf will add strength and rigidity to the shtender even if you don’t keep anything in there.)

Use 1.25″ screws and glue.

5) Fasten the shelf. use 1.25″ screws.

6) Fasten the shelf lip. use 1.25″ screws.

7) fasten the top lip to the top from underneath. Use screws that are long enough to secure the lip, but short enough that they won’t penetrate its top. you may want to sand the ends of the molding first for a more rounded appearance.

8) center the top and fasten it. some people put a small piece of wood at the angle between the top and side pieces and screw the top and sides into those to avoid having the top screwed only into end-grain. if possible, use 1 5/8″ screws, otherwise use 1 1/4″ screws.

tips:

-Sinking the screw-heads slightly below the wood’s surface will allow you to fill the holes and stain or paint them.

-you can cover ugly plywood edges with molding or iron on / press on edging that can be stained or painted.

-you can cut small 45-degree angles on the foot-tops to eliminate the corners.

-you can carve shallow .75″ notches for the footrest and shelf using a router and the appropriate bit with an angle guide. if you do this, make the notches very shallow, so as not to weaken the sides.

-the shelf back and lip can be placed inside the sides if you prefer. adjust the size by the 1.5″ thickness of the two sides.

-examine the lumber to ensure it’s straight, not full of knots, etc.

-don’t use redwood. it looks nice, but is soft and light.

You may have more fun experimenting and trying more elaborate designs and woods, like “Dr. Pepper” did.

As always, be careful and use goggles when using power tools.

Any questions? please ask.

hi I can only try,

Thanks so much for your detailed instructions. I’m gonna head over to hope depot this holiday weekend and jump right in. Starting with the legs, it seems like you gave instructions for 4 legs. I’m having difficulty picturing such a shtender. Perhaps you have a photo or a link to such a shtender. I can picture one where the two long side boards rest on two thick wooden blocks.

Kudos to ICOT for that very detailed post.

I’m not sure if anyone would still see this but I am also looking for help in building a Shtender except im going for a tabletop one. Can someone help me out and point me in the right direction? I want to make a tabletop shtender with the middle hollow so i can also put stuff it it. Im not sure how it will look when i post it but i drew my idea here:

__

|| – this middle space to put stuff in.

Thanks thats all for now! I’ll probably try this over the weekend

I know its been a year but is “i can only try” around for some shtender help? I’d like to build a table shtender which adjusts height and has a small compartment (.5 inch) for pens and paper on the bottom. adjustable degree level, any advice?

Just a bump, in case “CollegeBochur” missed the earlier reply.

Idea for table-top shtenders; one can now buy (order?) heavy Lucite shtenders (I don’t have a store address but they can be seen in Emunas Yisroel – 44th + 16th Ave and Raslowitz – 17 + 17th Ave. in BP).

Also Amazing Savings sells small Lucite shtenders (probably for lap-tops) at $2.99!!. It does the trick. Easily portable. Get one for the country.

For personalization, order Hebrew name plates at any s’forim store.

Would like to hear comments from CR’s after purchase.

That’s an impressively short list.

And I’m sure if you take the potato chip bag when there is only one chip left, you’ll be able to cross that one off your list.

For chewing gum and walking in a straight line:

Start off slow. Chew your gum once, then take a step, chew, step, chew, step. I can’t do it myself, but my wife is quite the multi-tasker.

Derech HaMelech–

?

mghanooni–

You can place the hinge(s) on the bottom, left or right of the door, depending on whether you want it to swing down, to the left or to the right.

You can use a couple of small hinges or one long hinge (called a piano hinge).

You will need to make sure the door clears the downward-angled shtender top when it opens. If you don’t want a gap above the door, you can add a small lip to the underside of the shtender top that is even with or lower than the lowest point of the shtender top.

You can use a cabinet-door latch to hold the door shut.

If you have additional questions or would like clarification on anything, don’t hesitate to post here.

Post some pictures?

make sure to use screws, and dont cheap out on sanding. make your little brothers sand. dont skimp on the wood;a plywood shtender may make it for a few, but solid oak or the like will be rock solid for a looong time.

I have too many Shtenders. My father used to get the Goyim to make them for him in the woodworking shop -where he used to teach.

I can only try are you still on I want to build a tabletop shtender with a compartment door that swings down to be used as a sitting shtender